BMW Coding Thread

[shawnsheridan]

Originally Posted by charldev

I am looking to ship my F15 to Australia when we move there in a few months. Does anyone know if the navigation/connected drive will still function or how to code it that it does ?

Thanks,

I have no idea if Telematics (Connected Drive) will work in Australia. I think this is unlikely. But for Navigation, you will need to load Australia / New Zealand Map, so you just need Map and FSC Code.

[Grizzles]

I want to code my telephone setting default to "received calls" when I open instead of "phone book". Any thoughts?

[RajX5]

Hello, can someone PM me the latest software links? Mine is 2017 X5

[Almaretto]

Originally Posted by RajX5

Hello, can someone PM me the latest software links? Mine is 2017 X5

PM sent.

[RajX5]

Originally Posted by Almaretto

PM sent.

Thank you Almaretto...

[PeanutButterJellyTime]

Sorry if this has been brought up before but the number of posts in this thread made me scared to go through them all. I have thoroughly reviewed all information that were posted and have not seen anything to address this.

First of I would like to thank all involved in the step-by-step guide as it made it easy to learn the basics. For some reason I cannot download the information on the VO coding as it is something I will be using next.

I finally got down to doing some coding today so I was able to code a few simple codes, but as I coded them and exited esys and later turned it back on new .ncd files start to appear. I started off with maybe 8 and now I have 30+. Is this normal? To clarify I did save all 8 modules that initially appeared.

What I also noticed was that some of the modules (ICM, and many others) were not displayed until I rebooted esys. I figure that since these .ncd files are appearing that I should save them as they are the original configuration from the factory. Now I am just confused. Did I initially followed the steps wrong?

Would anyone be able to offer any guidance? Thanks in advance.

[Almaretto]

Originally Posted by PeanutButterJellyTime

Sorry if this has been brought up before but the number of posts in this thread made me scared to go through them all. I have thoroughly reviewed all information that were posted and have not seen anything to address this.

First of I would like to thank all involved in the step-by-step guide as it made it easy to learn the basics. For some reason I cannot download the information on the VO coding as it is something I will be using next.

I finally got down to doing some coding today so I was able to code a few simple codes, but as I coded them and exited esys and later turned it back on new .ncd files start to appear. I started off with maybe 8 and now I have 30+. Is this normal? To clarify I did save all 8 modules that initially appeared.

What I also noticed was that some of the modules (ICM, and many others) were not displayed until I rebooted esys. I figure that since these .ncd files are appearing that I should save them as they are the original configuration from the factory. Now I am just confused. Did I initially followed the steps wrong?

Would anyone be able to offer any guidance? Thanks in advance.

If you do not run engine, then some ECU's will not wake up and you will not see complete vehicle. There is no way your car only has 8; but the total number will vary depending on year and equipped packages.

Saving all NCD's is not necessary because you will unlikely code each one and can always VO code back to factory.

[PeanutButterJellyTime]

Thanks for your response Almaretto. I was just concerned that more NCDs were appearing and was afraid I did something wrong.

I think it is all good now and should have all the coding done by tonight.... I hope. I will read the attachments in your pm and see if it will provide all the answers that I need. Thanks.

[Rotzy]

Originally Posted by PeanutButterJellyTime

For some reason I cannot download the information on the VO coding as it is something I will be using next.

That link has never worked for me. However, just watch the third video titled "FA and VO Coding" and it will walk you through the VO coding process. I usually have it open on my laptop while I'm coding and literally follow it step by step.

Also, remember that any modules that you VO code will be reset to default and therefore you will loose the FDL coding you already completed. That is why you VO code first, then do your FDL coding.

[PeanutButterJellyTime]

Originally Posted by Rotzy

However, just watch the third video titled "FA and VO Coding"

Thanks for your response.

I did watch that exact video while trying to FA code and then VO code. However, the problem came when he said to right click the ECU folder and code. The procedure in the video didn't work for me as when I right click the ECU folder the code selection was grey (and the video apparently is grey as well). That's why I tried right click-->read coding. Then I was able to code. Not sure why this is.

[Rotzy]

Originally Posted by PeanutButterJellyTime

Thanks for your response.

I did watch that exact video while trying to FA code and then VO code. However, the problem came when he said to right click the ECU folder and code. The procedure in the video didn't work for me as when I right click the ECU folder the code selection was grey (and the video apparently is grey as well). That's why I tried right click-->read coding. Then I was able to code. Not sure why this is.

Ahhh, above my knowledge level! @Almaretto will get you straightened out.

[Almaretto]

Originally Posted by Rotzy

Also, remember that any modules that you VO code will be reset to default and therefore you will loose the FDL coding you already completed. That is why you VO code first, then do your FDL coding.

I tend to avoid the word "default" and use "factory" instead.

Originally Posted by PeanutButterJellyTime

Thanks for your response.

I did watch that exact video while trying to FA code and then VO code. However, the problem came when he said to right click the ECU folder and code. The procedure in the video didn't work for me as when I right click the ECU folder the code selection was grey (and the video apparently is grey as well). That's why I tried right click-->read coding. Then I was able to code. Not sure why this is.

Certain E-sys functions are only available under specific conditions. To VO code, you should be able to do one of the following:

• Right click ECU folder > "Code"
• Left Click ECU Folder > "Code" Button

You do not need to "Read Coding Data" first. I just tried 'offline' & connected without issue.
For FDL Coding, if you select orange CAFD, only "Code FDL" button will be available.

[tronronjohn]

Hello, can someone PM me the latest software links? Mine is 2014 X5

[shawnsheridan]

Originally Posted by pineradylan

Hello, can someone PM me the latest software links? Mine is 2014 X5

No. You cannot Send or Receive PM's yet. Send me one when you can.

[h3nrytan]

Hello Shawn, could you please pm me the latest software please. TQVM

[shawnsheridan]

Originally Posted by h3nrytan

Hello Shawn, could you please pm me the latest software please. TQVM

PM sent.

[PeanutButterJellyTime]

I have managed to get most of the coding done and am confident to say I could be of help in providing any advice to new coders. I did it all manually so that I can understand the ins and outs. However, there are a few I can't figure out and it would be great if someone can provide some insight.

1. I cannot find the correct path to get the turn signals blink 5 times. I even tried using the cheat to code it and it does not work. Any clue why or is it possibly another path?

2. Everytime I try coding for camera on at all times, it gives me an error saying I need more memory and to reboot the software. I even tried coding one of the four at a time but same error. Does anyone know why? I have tried rebooting etc so please don't give the IT famous response. 🤔

3. It's awesome to be able to mirror my phone in to the Idrive screen, but I don't see an office menu in my communications menu where all the features can be organized. Also, I can't find REMINDER_TRIGGERS_EIN_AUS to activate it.

I think this list comprise of the features I really want. I hope someone can help me out.

BTW, setting USB to 2100ma does not work with my Samsung S6 edge. I was hoping it would so that I can get quick charge to work through the USB.

[Rotzy]

Originally Posted by PeanutButterJellyTime

1. I cannot find the correct path to get the turn signals blink 5 times. I even tried using the cheat to code it and it does not work. Any clue why or is it possibly another path?

http://f15.bimmerpost.com/forums/sho...postcount=3169

[PeanutButterJellyTime]

Originally Posted by Rotzy

http://f15.bimmerpost.com/forums/sho...postcount=3169

Thanks Rotzy! It works now. I was only on page 9 of this thread so you saved me.

[Rotzy]

Originally Posted by PeanutButterJellyTime

Thanks Rotzy! It works now. I was only on page 9 of this thread so you saved me.

No problem. I'm not sure who does it, but it would be great if we can get the cheat sheet updated with the new info.

[xdriverx]

Planning on getting delivery of my new X5 end of April. Anyone in the NYC area (Queens) who can help me code the car? Looking to turn on the anti-dazzle feature and any other recommendations. Will pay you beer or cash

[igeneo]

My F15 should be here soon... Since coding is new to me and I likely would not attempt on my own, I was wondering if there was a common list of what most users are choosing? (sorry if this is not the right place for this)

I'm thinking my short list would be:

• Turn On Zoom Feature For Rear View Camera
• Disable Legal Disclaimers (Startup, Camera, Etc.)
• Enable Tire Pressure & Temperature Readings In iDrive
• Transfer Phone’s Ringtone To Vehicle (iPhones Only). 2011+ Models Only
• Change US Nav Voice To UK Nav Voice
• Change US Nav Voice To UK Nav Voice
• Close Windows & Sunroof With KeyFob
• Fold/Unfold Side Mirrors With KeyFob & Comfort Access
• Fold Side Mirrors As Soon As The Vehicle Is Locked
• Unlock Doors When Car Is Turned Off
• Disable Interior Alarm Motion Sensor (we have a dog)
• Close Trunk From Key & Interior Button
• Disable Auto Start/Stop (A.S.S) OR Code It To Last Memory Setting
• Disable Angel Eye Dimming
• Enable Fog Lights As Welcome Lights
• Run High Beams & Fog Lights Simultaneously
• Enable Brake Force Braking
• Enable Fog Light Functionality While The Light Switch Is In The Parking Light Position
• European High Beam Assist
• Enable Door Handle Lights To Come On When Car Is Put In Reverse
• Blinkers In HUD
• Digital Speedometer
• Disable Top Speed Restriction For Cameras
• Adjust The Temperatures For Seat Cooling
• Enable Launch Control

Is there anything "critical" for an F15 that I may be missing? (no need for video in motion)